BEASTX MICROBEAST PLUS HD Pro Edition

MICROBEAST PLUS HD Pro Edition is a 3-axis control system for flybarless RC model helicopters. MEMS sensors of the latest generation measure the aircraft′s rotational movement with unprecedented precision and transmit the data digitally and in real time to the system.
The housing made of plastic composite material keeps the weight of MICROBEAST PLUS sensationally low.

The sophisticated setup can quickly be done everywhere and no expensive programming box or computer is needed. So many settings can also be changed simply and easily at the flying field.
Further options are available with the optional USB2SYS interface and the StudioX software package. MICROBEAST PLUS can be kept up to date by using the update functionality and advanced pilot can thus customize the unit specifically to their needs.

The device comes with Firmware ProEdition (V5.2): Additional to basic functionality as flybarless and tail gyro system, an internal RPM Governor function for helicopters with electric or combustion drive is included as well as the AttidudeControl function which can level the helicopter automatically. This allows to activate different training aids like bail out rescue mode, 3D-Mode or flight trainer mode.

This version is designed as "Heavy Duty" version of MICROBEAST PLUS Pro Edition with an additional switchable high power input. It is particularly suitable for helicopters with standard sized servos and it reflects today‘s requirements for power supply like never before. The power supply port is realized by a well proven, high-quality connector. By using the included switch, the system can be activated electronically and remains operational even if the switch is disconnected by accident. Due to this fact the high power connection may be used without the switch at all. MICROBEAST PLUS HD has a housing in aluminum composite construction.

Governor mode :

The RPM Governor can be used for electric and nitro helicopters. It has built in soft start and autorotation bail out function. The control it quite similar to electric speed controllers with governor function, so you simply set your throttle curves as switches for "motor off", "headspeed 1", "headspeed 2" and "autorotation bailout".
Adjusting complex throttle curves is not necessary anymore and the helicopter will maintain the specified rotor head speed over the whole flight. Optional the nitro governor can be also used in classic style with throttle curves and a separate switch for governor/rpm control.

Attitude Control :

"Attitude Control" offers different modes of self leveling. These are "Bailout rescue mode", "3D-Mode" and "Flighttrainer mode" with angular limitation. Basically when you activate the Attitude Control it will turn your helicopter back to level position when you release the sticks. 
Some modes additionaly apply collective pitch input and lock your thrust stick in the ground direction. So the unit will turn your helicopter and keep it leveled in hovering flight regardless of how the pilot moves the stick.

Try everything and improve your skill with Microbeast Plus HD Pro Edition !

Specifications:

Input voltage : 3,5 V - 8,5 V DC (Operation with 2 cell LiPo possible)
Processor : 32 Bit ARM
Sensor : 6-Axis MEMS (Gyro + Accelerometer)
Dimensions : 36 x 25 x 21mm
Weight (w/o wiring) : 19g

Servo center pulses:
• Swashplate: 1520µs
• Rudder: 1520µs, 960µs, 760µs

Servo pulse rates:
• Swashplate: 50 - 200Hz
• Rudder: 50 - 560Hz

Swashplate mixing:
• mCCPM, eCCPM: 90, 120, 135, 140
• Swash phasing (by using StudioX)

Input signals:
• Single channels
• PPM serial pulse
• SRXL (JR XBus, SUMD, M-Link...)
• Futaba S.Bus/S.Bus2
• Spektrum Remote Receiver* (DSM2/DSMX) * with Spektrum Remote Receiver adapter

In the box :

• MICROBEAST PLUS HD Pro Edition
• Switch harness
• Power cable
• Receiver connection cables
• 3M adhesive pads
• Adjustment tool
• Printed instruction manual

Accessories:
• USB2SYS Interface
• Spektrum Remote Receiver adapter

Downloading : User Manual